A BMW drivetrain malfunction warning is one of the most common, and most confusing, messages a BMW owner can see. It usually appears suddenly, often with the yellow engine light, and the car may lose power until it is restarted. The message is not the name of a broken part. It means one of the car’s powertrain control units has stored a fault that affects how power is made or delivered, and BMW’s own service bulletins tie the same warning to causes as different as misfires, VANOS faults, boost control software and electric-drive faults.
This guide explains what the drivetrain malfunction warning means, the exact message variants owners report, whether it is safe to keep driving, the most common causes by engine, the fault codes BMW lists in its bulletins, realistic US repair costs, recalls and warranty extensions, and how to reset and diagnose it properly. It is part of the AMGRSM BMW and BMW M problems and reliability hub, and it draws on BMW of North America bulletins and recall documents filed with NHTSA, NHTSA owner complaint data and independent cost sources.
Short answer: “Drivetrain malfunction” means the engine computer (DME), or another powertrain module, has detected a fault and is limiting power to protect the car. If the car still drives smoothly, drive gently to a shop. If the engine light is flashing, the engine is shaking, oil pressure or temperature warnings appear, or the message tells you to stop, pull over safely. The cause lives in the stored fault codes, so have the fault memory read with BMW-capable software before any parts are replaced.
BMW Drivetrain Malfunction at a Glance
The table summarizes the causes that BMW bulletins, recall documents and NHTSA owner complaints link to the drivetrain malfunction message. Each one is explained further down, with costs in a separate section.
| Cause | Typical signs with the warning | Engines or models documented | Usual fix |
|---|---|---|---|
| Misfire (coils, spark plugs, injectors) | Rough running, shaking, flashing engine light | Any gasoline BMW; false misfires on the N63T per SI B12 10 16 | Replace the failed coil, plug or injector; software on affected N63T cars |
| VANOS (variable cam timing) faults | Reduced power, engine light, cam position codes | B38, N20, N26, N55, N63T, S55, S63T built to 10/31/2015 (SI B12 26 14) | ISTA test plan, VANOS repair if needed, DME software |
| Boost control faults | Sudden power loss under load, boost codes | F87 M2 built to 8/3/2016 (SI B12 17 16); B48 wastegate controller on X2 M35i and M235i Gran Coupe (SI B01 02 25) | DME software (M2); wastegate valve controller (B48, extended warranty) |
| Boost leaks (cracked charge pipe) | Loud pop, then limp mode and hissing under throttle | N55 and N20 cars such as the 335i, 435i, M235i and 320i (BimmerQuote) | New charge pipe, often an aluminum upgrade |
| Valvetronic faults | Engine light, misfires, boost shutdown | G12 7 Series with the N63R (SI B12 19 16) | Harness connector check, wiring harness or servomotor |
| Fuel delivery faults | Power loss, stalling, long cranking | 2018 M5 recall 18V-323; fuel pumps in owner complaints | Software (M5 recall) or a new fuel pump |
| Timing chain or oil pressure failure | Low oil pressure warning, noise, engine shuts off | Owner complaints on 2012–2015 N20 cars such as the 328i and 528i | Timing chain and guides; engine replacement if damaged |
| Hybrid and EV drive faults | “Stop carefully” messages, limited or no drive | X5 xDrive40e and i3 (SI B61 46 17); i4, i5, i7 and iX (SI B12 05 23) | Software and calibration, or eDrive motor cleaning |
What Does Drivetrain Malfunction Mean on a BMW?
BMW uses Check Control messages to report faults. The drivetrain malfunction message is raised when the DME (the gasoline engine computer; DDE on diesels) or another powertrain module stores a fault serious enough to switch to a protective strategy. That usually means reduced torque, so the car feels slow, but the car is still telling you the fault exists rather than what it is.
BMW’s bulletins use the plain wording “Drivetrain Malfunction”. For example, SI B12 10 16 describes the message “displayed with reduced engine power” on N63T V8 models, and SI B12 26 14 says the engine “could go into a reduced power mode with the ‘Drivetrain Malfunction’ message displayed.” The wording on the screen varies by model and software. Messages quoted in BMW documents and NHTSA owner complaints include:
- “Drivetrain malfunction. Drive moderately. Maximum drivetrain output not available. Consult service center.” This is the full version quoted in NHTSA complaints about the 2013 328i xDrive and 2013 328i.
- “Drivetrain malfunction. Stop carefully and turn off vehicle.” This and “Drivetrain malfunction. Limited Range and drive power. Engine restart may not be possible” are listed for the X5 xDrive40e plug-in hybrid and the i3 in SI B61 46 17.
- “Continued driving possible: Drivetrain Electric drive limited.” Owners of newer plug-in hybrids quote this alongside “Power Supply Drivetrain Malfunction”, for example in a complaint about the 2023 X5.
The difference matters. “Drive moderately” and “continued driving possible” mean the car has judged it safe to keep moving with limited power. “Stop carefully” means it has not. The related “Transmission malfunction” or “Gearbox malfunction” messages point at the gearbox rather than the engine and are covered below.
Is It Safe to Drive With a BMW Drivetrain Malfunction?
Sometimes, briefly. The safest approach is to let the car’s own message and behavior decide:
- Stop as soon as it is safe if the message says to stop, the engine light is flashing, the engine shakes badly, the red oil pressure or coolant temperature warning comes on, or the car keeps stalling. A flashing engine light indicates a misfire, and RepairPal warns that continuing to drive can damage the catalytic converter, which can cost more than $1,000 to replace.
- Drive gently to a shop if the engine runs smoothly and the message says to drive moderately. Avoid full throttle, towing and high-speed passing, because power can drop again without warning.
- Do not ignore a message that clears. In SI B12 10 16, BMW notes that cycling the ignition clears the warning, but the fault is still stored in the DME. Several NHTSA complaints describe a warning that came and went before a larger failure.
Low oil pressure together with drivetrain malfunction is the most serious combination. In NHTSA’s complaint data, 24 complaints about 2012–2015 2, 3, 4 and 5 Series, X1, X3 and Z4 models mention oil pressure alongside the drivetrain message, and several describe the engine shutting down soon after. Switch off the engine immediately if both appear.
Common Causes of the BMW Drivetrain Malfunction Warning
The message is generic, but the causes repeat. These are the ones with the strongest documentation, starting with the most common on gasoline cars.
Misfires: ignition coils, spark plugs and injectors
A misfire is the classic trigger. Worn spark plugs or a failed coil cause rough running, shaking at idle, a flashing engine light and the drivetrain warning. Generic misfire codes start with P030, for example P0301 for a cylinder 1 misfire as listed by RepairPal, and BMW’s own codes such as 140001 (“Misfires, several cylinders: injection is switched off”) and 140501 to 140801 for cylinders 5 to 8 appear in SI B12 19 16. On turbo direct-injection engines, a leaking injector can cause the same symptoms. A technician will usually swap the coil to another cylinder to see whether the misfire follows it.
Software and false fault detection
Not every warning means a failed part. BMW has issued several bulletins where the fix was new software:
- SI B12 10 16 (April 2016) covers the 7 Series (F01, F02), 6 Series (F06, F12, F13) and 5 Series Gran Turismo (F07) with the N63T engine produced to 7/2013. The warning appears after several hours at constant highway speed with light throttle, with erroneous misfire faults for cylinders 3 and 6. The fix is to reprogram the car.
- SI B12 17 16 (August 2016) covers the F87 M2 produced up to 8/3/2016. Faults 120208 and 120408 switch off boost pressure control because of an overly sensitive diagnostic threshold, and the fix is a DME update.
VANOS and timing faults
BMW’s SI B12 26 14 (revised March 2016) covers all models with the B38, N20, N26, N55, N63T, S55 and S63T engines and Bosch DME produced to 10/31/2015. The engine light comes on and the engine can enter reduced power with the drivetrain malfunction message, while VANOS faults are stored “although the engine is mechanically sound.” The cause was unfavorable Engine Position Management parameters in the DME software. The bulletin adds an important exception: on N55 engines produced up to October 2011, bolts in the VANOS adjustment unit may be loose or broken, so those cars need a mechanical check. For the oil-pressure VANOS codes 2A82 and 2A87, see the BMW 2A82 and 2A87 codes guide.
On the S55 in the M2 Competition, M3 and M4, a sudden drivetrain malfunction right after a hard pull or downshift is also a known sign of crank hub slip, which is explained in the BMW S55 problems guide.

Boost leaks and turbo control
Turbocharged BMWs cut power when boost does not match what the DME expects. A cracked plastic charge pipe is a well-known example on N55 and N20 cars: owners describe a loud pop, then limp mode and the drivetrain warning, according to BimmerQuote, and retailers such as ECS Tuning sell aluminum replacements because the original plastic pipe can crack. Wastegate problems are the other turbo-related cause. BMW’s SI B01 02 25 (May 2025) says the turbocharger wastegate valve controller on the B48 engine may fail internally, triggering drivetrain malfunction messages, wastegate activation codes and lost power. It extends the warranty on that part to 15 years or 150,000 miles for the 2019–2022 X2 M35i (F39) and 2020–2023 M235i xDrive Gran Coupe (F44) within the listed production dates. Owners of other B48 cars can find more in the BMW B48 engine problems guide.
Valvetronic wiring on V8s
SI B12 19 16 (August 2016) covers the G12 7 Series with the N63R V8. A connector on the engine wiring harness that is not fully locked, or poor pin contact, sets Valvetronic faults such as 136608 and 135808, followed by consequential boost and misfire faults. BMW tells technicians to check for water in the DME connectors, then check the connector or replace the Valvetronic harness, and notes that the servomotor itself “is not normally the problem.” The wider V8 picture is in the BMW N63 engine problems guide.
Fuel delivery problems
Low fuel pressure makes a BMW lose power or stall, and the drivetrain warning often comes with it. The clearest official example is recall 18V-323: on 2018 M5 (F90) cars produced through April 17, 2018, BMW says fuel pressure “can drop causing a power loss, and possibly engine stalling,” with the engine light and the Drivetrain Malfunction message illuminated. The remedy was a free software update. Fuel pumps also appear in 40 of the drivetrain complaints analyzed below.
Timing chain and oil pressure failures on N20 engines
The largest single cluster in NHTSA’s complaint data comes from 2012–2015 cars with the N20 four-cylinder, such as the 328i and 528i. Many owners describe a low oil pressure warning followed by drivetrain malfunction and the engine shutting off, and several say a dealer found a failed timing chain or guide. These are owner reports, not BMW findings, and NHTSA’s recall records for these models do not include a timing chain recall. They are still a strong reason to treat this combination of warnings seriously and to ask for timing chain service history when buying an N20 car.
Transmission Causes
The drivetrain warning is usually engine-related, but gearbox faults can also reduce power or appear alongside it. BMW is a major customer of ZF’s 8HP eight-speed automatic, which was first used in the F01 7 Series, according to Wikipedia. When the gearbox has its own fault, BMWs normally show a transmission or gearbox message instead. The X5 xDrive40e and i3 bulletin (SI B61 46 17), for example, lists “Gearbox malfunction. Gearbox position P might not be possible” next to the drivetrain messages.
If the drivetrain warning comes with harsh shifts, a gearbox stuck in one gear, flaring revs or a transmission message, the transmission control unit’s fault memory must be read as well. A generic code reader usually reads only the engine computer, so BMW-specific diagnostic software is needed.

Hybrid and Electric BMWs
On plug-in hybrids and electric BMWs, the same message can come from the high-voltage system, and it can be more urgent because the car may lose drive completely:
- SI B61 46 17 (December 2017) covers the F15 X5 plug-in hybrid (xDrive40e) and the i3 and i3 REx. Drive power may be restricted or drive mode may not engage. The cause is software in the electrical machine electronics (EME), and BMW states that “parts replacement will not provide a solution”; the fix is reprogramming and a rotor position sensor adjustment.
- SI B61 38 14 (June 2016) covers the i3 and i3 REx with the Drivetrain Malfunction message (Check Control message 794) and high-voltage isolation faults, which can come from a cable defect or moisture in the range extender’s electric machine.
- SI B12 05 23 (revision 3, March 2026) covers the i4 (G26), i5 (G60), i7 (G70) and iX (i20) built up to 11/2023. A Drivetrain Malfunction message comes with isolation faults 0317F1 and 0317F2 in the combined charging unit, and the cause can be a metal chip or contamination behind the eDrive motor’s brush module. The fix is cleaning the rotor and brush module, under the new vehicle warranty or the Certified Pre-Owned program.

BMW Drivetrain Malfunction Fault Codes
BMW stores its own hexadecimal fault codes in addition to generic OBD-II P-codes. The codes below come directly from the BMW documents linked in each row. A code alone does not prove that a bulletin applies, since each bulletin also lists the models and production dates.
| Code | BMW description | Models or engines | Source |
|---|---|---|---|
| 120208 | Charging pressure control plausibility: pressure too high | F87 M2 | SI B12 17 16 |
| 120408 | Charging pressure control: switching off | F87 M2; also a consequential fault on the N63R | SI B12 17 16, SI B12 19 16 |
| 2D55, 131501 | VANOS faults handled with a separate software level | B38, N20, N26, N55, N63T, S55, S63T | SI B12 26 14 |
| 136608 / 135808 | Valvetronic servomotor 2 / 1, position sensors, signal: not plausible | G12 with N63R | SI B12 19 16 |
| 140001 | Misfires, several cylinders: injection is switched off | G12 with N63R | SI B12 19 16 |
| 222011 | Electrical machine angle sensor adjustment not carried out or rotor position sensor deviation not in tolerance | X5 xDrive40e, i3 | SI B61 46 17 |
| 22280F, 222814 | EME isolation faults | i3, i3 REx | SI B61 38 14 |
| 0317F1 / 0317F2 | High-voltage system insulation resistance below warning threshold / insulation fault detected | i4, i5, i7, iX built to 11/2023 | SI B12 05 23 |
Generic scan tools often show only a P-code such as a misfire or boost code, or nothing at all for other modules. BMW dealers use ISTA, and independent BMW specialists use ISTA or equivalent software that reads every control unit.
Which BMWs Get the Warning Most? NHTSA Complaint Data
To see where the warning shows up in practice, AMGRSM searched NHTSA’s public complaint database for BMW cars and SUVs from the 2006 to 2026 model years. Of 17,528 complaints returned, 397 unique complaints contain the phrase “drivetrain malfunction” (or “drive train malfunction”) in the owner’s description. This is a lower bound, because owners do not always quote the message. The search was run on November 21, 2026.
| Model family | Complaints naming the message | Peak model years |
|---|---|---|
| 5 Series | 126 | 2011–2013, most for 2012 |
| 3 Series | 102 | 2012–2015, most for 2013 |
| X5 | 53 | Spread across 2016–2026, most for 2024 |
| X3 | 22 | 2020 |
| 7 Series | 17 | 2009–2013 |
| 6 Series | 15 | 2013 |
| 4 Series | 13 | 2014 |
Some complaints list more than one model, so the rows do not add up to 397. The most frequent themes in the descriptions were highway driving (127 complaints), stalling or the engine shutting off (104), a recall being mentioned (95), oil (95), timing chain (43), fuel pump (40) and battery (32). Complaints are unverified owner reports and are not adjusted for how many cars were sold, so they show patterns, not failure rates. The pattern is still clear: 2011–2015 3 and 5 Series cars produce the most reports, and newer complaints are spread across X5 and X3 models, including plug-in hybrids.
BMW Drivetrain Malfunction Repair Cost
The cost depends entirely on the cause. The ranges below are published US estimates for common causes, not BMW prices, and they exclude taxes and local labor differences.
| Repair | Typical US cost | Source |
|---|---|---|
| Diagnosis (fault memory read and testing) | $159–$233 | RepairPal, BMW 335i |
| Ignition coil replacement | $146–$210 | RepairPal, BMW 328i |
| Spark plug replacement | $347–$467 | RepairPal, BMW 335i |
| Charge pipe replacement (N55/N20) | $500–$1,400 at independent shops, $600–$1,900 at dealers | BimmerQuote; aluminum pipe parts listed at ECS Tuning |
| Fuel pump replacement | $1,889–$2,151 | RepairPal, BMW 335i |
| N20 timing chain and guides | $2,000–$4,000 at independent shops, $3,500–$7,000 at dealers | BimmerQuote |
| Software update under a BMW bulletin | Covered under the BMW New Vehicle Limited Warranty when the car is within coverage | SI B12 17 16, SI B61 46 17 |
Warranty matters. BMW’s 2023 warranty booklet lists a New Vehicle Limited Warranty of 4 years or 50,000 miles, and the federal emissions warranty covers specific emission control parts, including the catalytic converter and engine control module, for 8 years or 80,000 miles. A misfire or engine computer fault on a younger car may therefore be covered, and the B48 wastegate controller extension described above runs to 15 years or 150,000 miles on eligible X2 M35i and M235i Gran Coupe cars. Always ask the dealer to check the VIN for open campaigns and extended coverage before paying.
Recalls That Mention the Drivetrain Malfunction Message
Most drivetrain warnings are handled through repairs and bulletins, not recalls. The recalls below are listed because their official NHTSA documents name the affected models and describe a drivetrain malfunction message.
| Recall | Models named | What the document says | Remedy |
|---|---|---|---|
| 18V-323 | 2018 BMW M5 (F90) produced through April 17, 2018 | Fuel pressure can drop, causing power loss and possible stalling, with the engine light and the Drivetrain Malfunction message | Free control unit software update (NHTSA record) |
| 20V-601 | Certain 2020–2021 330e, 530e, 745Le, X3 xDrive30e, X5 xDrive45e and i8 plug-in hybrids | Debris in high-voltage battery cells could cause a short circuit; an “HV Battery/Drivetrain malfunction” message may display and the car may enter failsafe mode | Battery inspection and module replacement as needed (NHTSA record) |
| 22V-683 | One 2022 BMW 745e | Battery cell short-circuit risk; an “HV Battery/Drivetrain malfunction” warning may display | Battery cell module replacement (NHTSA record) |
Other recalls can cause similar symptoms without mentioning the message. For example, recall 15V-189 replaced fuel pumps that could fail and stall the engine on certain 2014 228i, M235i, 320i, 328i, 335i, 428i and 435i models and some 2015 4 Series Gran Coupes. Run any VIN through the NHTSA recall lookup before diagnosing a warning.
How to Reset the BMW Drivetrain Malfunction Warning
Owners often search for a reset, and the honest answer is that the warning can clear itself, but the fault cannot be reset away.
- Pull over safely and switch off. If the car drives normally after a restart, the fault was intermittent. BMW’s N63T bulletin confirms that cycling the ignition clears the message.
- Do not clear codes before diagnosis. Clearing the fault memory with a scan tool or disconnecting the battery erases the freeze-frame data a technician needs, and the message will return if the cause remains.
- Read every module. Ask for a full BMW-level scan of the DME and transmission control unit, plus the high-voltage modules on hybrids and EVs.
- Check software and bulletins. Ask whether the car is at the latest software integration level and whether a bulletin such as SI B12 26 14 or SI B12 17 16 applies to the VIN.
- Fix the cause, then clear the codes. Once the repair is done, the technician clears the memory and road-tests the car to confirm the warning does not return.
Used BMW Buyer’s Checklist
- Scan before buying: a pre-purchase inspection should include a full scan of stored and recent faults, not just a check that the dashboard is clear.
- Ask about past warnings: a seller who mentions drivetrain malfunction messages “that went away” should be able to show the diagnosis and repair invoice.
- N20 cars (2012–2016 328i, 428i, 528i, 228i, X1, X3 and Z4 28i): listen for timing chain whine on a cold start and ask for timing chain service records, given the complaint pattern above.
- N55 cars: check whether the plastic charge pipe has been replaced, and for N55 engines produced up to October 2011, whether the VANOS unit was inspected per SI B12 26 14.
- S55 M cars: ask whether the crank hub has been upgraded, especially on tuned cars; the S55 guide explains why.
- B58 cars: the BMW B58 problems guide covers the oil filter housing, PCV and coolant issues to check.
- Plug-in hybrids and EVs: confirm that recalls such as 20V-601 are complete and ask the dealer whether SI B12 05 23 or SI B61 46 17 applies.
- Recalls and warranty: run the VIN on the NHTSA recall site and check remaining warranty and extended coverage with a BMW dealer.
More guides: For other engines, warning messages and fault codes, browse the Common Problems & Reliability Guides hub for BMW, Mercedes-AMG and Audi.
Frequently Asked Questions
What does drivetrain malfunction mean on a BMW?
It means the engine computer or another powertrain control unit has stored a fault that affects power delivery and has switched to a protective mode, usually with reduced power. BMW’s bulletins link the message to causes ranging from misfires and VANOS faults to boost control software and electric-drive faults, so the stored fault codes are needed to find the cause.
Can you keep driving with a BMW drivetrain malfunction warning?
If the car runs smoothly and the message says to drive moderately, you can usually drive gently to a shop. Stop as soon as it is safe if the message says to stop, the engine light flashes, the engine shakes, or a red oil pressure or temperature warning appears. A flashing engine light indicates a misfire that can damage the catalytic converter, according to RepairPal.
What is the most common cause of drivetrain malfunction on a BMW?
On gasoline BMWs, misfires from worn spark plugs or failed ignition coils are among the most common causes, followed by boost leaks, VANOS faults and fuel delivery problems. On 2012–2015 N20 four-cylinder cars, many NHTSA complaints describe a low oil pressure warning and timing chain failure together with the message.
How much does it cost to fix a BMW drivetrain malfunction?
It depends on the cause. Published US estimates range from about $159–$233 for diagnosis and $146–$210 for one ignition coil (RepairPal) to $1,889–$2,151 for a fuel pump on a 335i (RepairPal) and $2,000–$7,000 for N20 timing chain work (BimmerQuote). Software fixes under BMW bulletins are covered while the car is under warranty.
How do you reset the drivetrain malfunction warning on a BMW?
Switching the car off and restarting it often clears the message, as BMW’s SI B12 10 16 notes, but the fault stays stored. Clearing codes or disconnecting the battery does not fix the cause and erases useful diagnostic data. Have the fault memory read first.
Is there a recall for BMW drivetrain malfunction?
There is no single recall for the message. Recalls whose documents mention it include 18V-323 for the 2018 M5, 20V-601 for certain 2020–2021 BMW plug-in hybrids and 22V-683 for one 2022 745e. Check any VIN on the NHTSA recall site.
Can a weak battery cause a BMW drivetrain malfunction?
Battery problems are mentioned in 32 of the 397 NHTSA complaints that quote the message, but complaints do not prove cause. BMW bulletins require a stable power supply during programming, and a weak battery should be tested and ruled out during diagnosis. The BMW increased battery discharge guide explains battery testing and registration.
The Bottom Line on BMW Drivetrain Malfunction
A BMW drivetrain malfunction warning is a protective message, not a diagnosis. BMW’s own bulletins show it can come from a misfire, a VANOS or boost control software fault, a loose Valvetronic connector, a fuel delivery problem or, on hybrids and EVs, the high-voltage system. Take the message’s own instructions seriously, stop immediately if oil pressure or a flashing engine light comes with it, and have every control unit scanned before replacing parts. With the right diagnosis, many causes are inexpensive, and some are covered by warranty, extended coverage or recalls.
Sources and notes: Service bulletins are BMW of North America documents filed with NHTSA and linked above: SI B12 10 16, SI B12 17 16, SI B12 26 14, SI B12 19 16, SI B61 46 17, SI B61 38 14, SI B12 05 23 and SI B01 02 25. Recall details come from NHTSA documents for 18V-323, 20V-601, 22V-683 and 15V-189. Complaint counts come from NHTSA’s public complaint data, searched on November 21, 2026. Warranty terms come from BMW’s 2023 warranty booklet. Cost ranges come from RepairPal, BimmerQuote and ECS Tuning, not from BMW, and may change. This article is for general information. Confirm any diagnosis, bulletin or recall status for a specific vehicle with a BMW dealer or a qualified specialist.




